How to do routine maintenance of the kitchen sink?
1. Cautions in routine maintenance: Keep articles that are prone to rusting away from prolonged contact with the kitchen sink. Clean the kitchen sink after each use and wipe it dry with a cloth. Try to keep the kitchen sink surface as dry as possible.
2. Unexpected behaviors in cleaning: To remove mineral deposits on the bottom of the kitchen sink, use diluted vinegar. Afterward, rinse with water. Avoid using steel wire balls or abrasive cleaning materials to clean the kitchen sink.
3. Unexpected behaviors in routine maintenance: Avoid leaving pickles, other pickled foods, mayonnaise, or mustard in the kitchen sink for extended periods of time. Also, do not leave rubber placemats, wet sponges, or cleaning sheets in the kitchen sink overnight.
How about the size of the kitchen sink edge reserved?
Ensure a minimum of 40~50mm of space.
How to remove the rust on the kitchen sink?
For rusted areas, use a damp cleaning cloth or cotton cloth (instead of steel wire balls) with a small amount of cleaning powder (such as toothpaste). Gently rub back and forth and then rinse with water.
How to solve the problem of foam coming out of the overflow port?
As an auxiliary accessory, the overflow pipe is used to drain the remaining liquid into the waste pipe. It is connected to the waste pipe. After pouring the foaming agent and water into the kitchen sink, the water will be drained through the waste pipe due to its heavy weight. The air pressure generated during this process will be relieved through the overflow pipe. The foam is light and bursts slowly. Consequently, the foam that bursts more slowly will be pushed out of the overflow port by the air pressure. Currently, JOMOO kitchen sinks and most other kitchen sink brands on the market do not have structures to prevent foam or water backflow. This is not a quality issue. It is recommended to use a small amount of dishwashing liquid when washing dishes.
Why is the kitchen sink scratched?
Each JOMOO kitchen sink is made of one-piece 304 stainless steel with low hardness due to a lack of surface treatment. It is suggested to wipe with a non-abrasive scouring pad.
Made of stainless steel with a Vickers hardness of 220 or so, the kitchen sink cannot be cleaned with steel wire balls or have collisions with sharp articles. It is made clear on both its care label and manual
How to protect the kitchen sink that has been installed but not used immediately after installation?
After installation, cover the kitchen sink with its PE bag (or the hole size reference board) to keep it from corrosion by dust or liquids during decoration.
How to maintain a bathtub?
a. In routine cleaning, clean the bathtub with soft cloth (or sponge) and clean water and wipe the stains on its surface gently with soft cloth and toothpaste. Wiping the scales with steel wire balls or hard brushes may cause scratches.
b. After each three months, clean the backwater strainer to avoid its blockage by hair or other foreign matters.
Most JOMOO bathtubs are made of acrylic, and only a few ones are made of cast iron.
Most JOMOO bathtubs are made of acrylic, while only a few are made of cast iron.
Grind the scratches with 2000-mesh fine abrasive paper and water.
To remove scratches, grind them with 2000-mesh fine abrasive paper and water.
How to install the angle valve or the cold tap?
1. Rotate to dismount the plug, turn on the water source, clean the inlet hose, and ensure there is no sand or foreign matter to prevent blockage during use.
2. Wrap PTFE tape clockwise around the G1/2 thread on the water inlet of the angle valve. If the angle valve has a decorative cover, mount it onto the angle cover first. Connect the angle valve to the water inlet connector by rotating them (tighten with a spanner). Install the angle valve according to the signs for cold and warm water.
3. Turn on the water source and then turn off the angle valve. After 5 minutes, check for leaks in the inlet hose and angle valve.
Why does the angle valve leak?
Figure out the leaking position. If it is due to a common fault of the connector, replace the gasket; if it is due to a common fault of the water outlet, have the water outlet wrapped with another turn of PTFE tape.
How to maintain the floor drain?
1. To clean the filter, remove the outer cover and filter layer. Use a toothbrush to remove hair and dirt. If the filter remains dirty, use neutral detergent. After cleaning, reassemble the filter layer and outer cover.
2. Maintain the water seal by providing regular water feed. If the floor drain won’t be used for an extended period, seal its outer cover.
3. To prevent blockages, regularly clean the floor drain and avoid disposing of foreign objects into it.
How to maintain the accessories?
1. Ensure good ventilation by frequently opening the bathroom door and window to promote fresh air circulation and maintain family health.
2. Avoid using corrosive detergents. Instead, wipe accessories with a soft cotton cloth and clean water to maintain their glossy appearance.
3. Clean the interior thoroughly every 3 months. After cleaning, wipe the accessory surfaces to prevent water stains.
How to clean the surfaces of polished or elaborately polished accessories of 304 stainless steel? (Accessories of models ending with "AB-1" are stainless steel ones.)
If there are rust spots on the surface of such an accessory, clean surface of the accessory thoroughly with mildew-proof water wax, rinse it and wipe the water on it with soft cotton cloth to make it glossy.
How to maintain the shower room?
a. When in use, do not hit the movable door, otherwise it may fall off.
b. In routine cleaning, flush with water. The scales on the glass surface can be wiped with soft cloth (or sponge) with a mixture of salt and white vinegar and then flushed with water; the scales on the frame can be removed with universal cleaner. Wiping the scales with steel wire balls or hard brushes may cause scratches.
Does the shower base of the shower room need to be embedded?
It can be embedded or non-embedded, depending on the customer's demand. An embedded shower base is nice and firmer and has better leakproofness.
Is there an explosion-proof film on the glass of the shower room?
The glass of each shower room bears an explosion-proof film on its external side.
Is the glass of the shower room tempered glass?
The glass of each shower room is tempered glass passing the 3C certification.
The main function of shower rooms is to separate the dry area from the wet area. Can the shower room completely avoid water leakage?
The shower room cannot avoid water leakage completely because it is not a molded one-piece product but a spliced product. In normal use, it does not leak seriously.
Does the dual explosion prevention function of the shower room mean that the shower room has two layers of explosion-proof film?
The dual explosion prevention function refers to the explosion-proof film and the explosion-proof tempered glass.
How to maintain the bathroom cabinet?
a. In each week, clean the bathroom cabinet and the bathroom sink with a soft cloth (or sponge) with household dishwashing liquid, clean the faucet with a wet soft cloth, and clean the makeup mirror with alcohol or glass cleaner. Wiping with steel wire balls or hard brushes may cause scratches.
b. If the screw on a slide, hinge, or handle is loose, have some 502 glue drip into the original screw hole and lock the screw after the 502 glue has cured.
Can another brand's liquid soap be used after the original liquid soap in the bathroom cabinet has run out?
Please use JOMOO liquid soap refills.
1. The liquid soap dispenser can be affected by the liquid soap used. If the liquid soap of another brand is used, the liquid soap dispenser may fail to work normally due to corrosion of its interior as a result of blockage and leakage.
2. If the liquid soap of another brand, which has a different concentration from JOMOO liquid soap, is used, the liquid soap discharge effect will be affected, and the pump will be overloaded. After long-time service, the air intake of the pump may leak, making the liquid soap dispenser abnormal due to interior corrosion and damage.
What is the material of the main cabinet?
Solid wood, stainless steel, composite boards, and PVC
What is the material of the makeup mirror?
Aluminized mirror, coppered mirror or copper-free mirror
Why is the color of the bathroom cabinet different from the color seen in the store?
The bathroom cabinets of different batch numbers may have slightly different colors.
Why is the liquid soap dispenser not responding?
1. Check whether the liquid soap dispenser is a rechargeable one. If it is, charge it and try again.
2. If the liquid soap dispenser is a rechargeable one, check and make sure its power plug is correctly inserted.
Why is the liquid soap dispenser of the new product not dispensing liquid soap?
Check whether the liquid soap dispenser is correctly installed. In its first use, try more times.
Why do the lights fail to turn on or adjust brightness?
1. Check whether the lights are correctly connected to the power source.
2. Check whether the hand waving is correct.
a. Hand waving: Move a hand leftward or rightward through the sensing range within 10 cm in front of the mirror to enable or disable the LED light. When waving the hand, keep all the fingers together (to avoid light leakage) and wave left and right at a uniform speed while the palm faces the mirror.
b. Sensor lights on both sides: Put a hand in a position less than 10 cm under the sensing point at the bottom of the light (the operation can be done from either side) to turn on or off the light.
3. Brightness adjustment: Put a palm in the sensing distance for some time.
What's the inlet water pressure of the touchless urinal?
There are two power supply modes to choose from. The standard configuration is the DC power supply mode.
How long is the sensor conductor of the touchless urinal?
What's the diameter of the inlet hose of the touchless urinal?
DN15 (G1/2" connecting thread)
What's the sensing distance of the touchless urinal?
The sensing distance can be automatically adjusted, with a maximum distance of 75cm.
What's the response time of the touchless urinal?
The response time for detecting the presence of a user is about 3 seconds, while the response time for detecting the absence of a user is about 1 second.
How long is the flush time of the touchless urinal?
Before use, it is recommended to flush for about 5 seconds. After use, the flush time can be controlled between 5 and 15 seconds (stepless control).
What's the inlet water pressure of the touchless urinal?
The minimum water pressure (dynamic pressure) required is 0.5kgf/cm², while the maximum water pressure (static pressure) allowed is 12kgf/cm². The optimal water pressure (static pressure) is between 3kgf/cm² and 5kgf/cm².
What's the water consumption of periodic flush of the touchless urinal?
The maximum water flow rate is about 2.5L per time, under a dynamic pressure of 0.1MPa. A flow regulator is provided.
How long is the life of the touchless urinal?
The product can be used for up to 300,000 times.
What's the power supply mode of the touchless toilet bowl?
There are two power supply modes to choose from. The standard configuration is the DC power supply mode.
How long is the sensor conductor of the touchless toilet bowl?
What are the diameters of the inlet hoses of the touchless toilet bowl?
Main inlet hose: DN32; branch inlet hose: DN25 (G1" connecting thread)
What's the sensing distance of the touchless toilet bowl?
The sensing distance can be automatically adjusted, with a maximum distance of 75cm.
What's the response time of the touchless toilet bowl?
The response time for detecting the presence of a user is about 10 seconds, while the response time for detecting the absence of a user is about 5 seconds.
What's the flush mode of the touchless toilet bowl?
Automatic single/dual flush (no bowl pre-wetting if the interval of use is shorter than 4 minutes)
What's the flush time of the touchless toilet bowl?
Bowl pre-wetting time: about 2s; flush time after use: about 5s (when the sensing time is shorter than 90s) or about 9s (when the sensing time is longer than 90s)
What's inlet water pressure of the touchless toi+C19let bowl?
Minimum water pressure (dynamic pressure): 0.5kgf/cm²; maximum water pressure (static pressure): 12kgf/cm²; optimal water pressure (static pressure): 3kgf/cm²～5kgf/cm²
What's the water consumption of periodic flush of the touchless toilet bowl?
Maximum: about 6L/time (under a dynamic pressure of 0.1MPa) (A flow regulator is provided.)
How long is the life of the touchless toilet bowl?
The product can be used for up to 300,000 times.
How to maintain ceramic products?
a. We recommend descaling a toilet or squatting pan every two weeks. Here’s the method: Pour toilet cleaner into the water seal (trap) of the toilet or squatting pan. After 15 minutes, clean the toilet or squatting pan using a toilet brush and flush it. Use a toilet brush with soft bristles to avoid damaging the glaze (avoid using tools like steel wire balls).
b. When flushing a toilet, avoid pressing both flush buttons simultaneously. If you do, the toilet will execute the ECO flush, resulting in poor flushing performance when dealing with a large amount of feces.
How to remove the scales on the water seal of the toilet?
1. If you’re using a toilet in an area with good water quality, clean it daily. Remove scales using dilute hydrochloric acid or an ordinary supermarket cleaner.
2.In regions with poor water quality (e.g., using seawater for flushing), clean the toilet weekly. Use Kangjie 99 Toilet Cleaner and scouring pads for scale removal.
3. If the toilet has hard water deposits or hasn’t been cleaned in a long time, wipe it with fine abrasive paper (with more than 1,000 meshes) using alcohol.
What's the rough-in of a toilet?
The rough-in of a toilet is the vertical distance between the center point of the waste pipe reserved in the floor and the finished tile surface. Typically, it’s either 305mm or 400mm. Here are the installation ranges:
1. For a 305mm rough-in, the range is 290-390mm.
2. For a 400mm rough-in, the range is greater than 390mm. Note: If the installation range is less than 290mm, installation will fail.
